۞۞ Shohag Gsm™ ۞۞
Welcome to ۞۞Shohag Gsm™ ۞۞ please join now !!!!

...!!! Keep share you knowledge!!!...
@};- @};-

If your Like Post please Comments

((((((((The most helping forum)))))))



 
HomeFAQSearchCracked ZoneRegisterLog inIMEI Chack

Share | 
 

 Mtk Android (Sp flash tool ) tutorial :)

View previous topic View next topic Go down 
AuthorMessage
Shohag Gsm™




Male Posts : 1531

Points : 74964
Reputation : 43
Birthday : 21/12/1989
Join date : 15/03/2011
Age : 26
Location : In your Hard

PostSubject: Mtk Android (Sp flash tool ) tutorial :)   Sat Nov 10, 2012 5:32 am

What's needed:


  • USB data cable
  • MediaTek USB VCOM drivers
  • SP Flash Tool ( Latest version SP_Flash_Tool_v3.1224.01)



  • First of all, make sure that you have MediaTek DA USB VCOM drivers installed.
[You must be registered and logged in to see this image.]
Flashing the whole ROM

  • First of all open SP Flash Tool, then click Scatter-loading button to load the correct scatter file

    (MT6575_Android_scatter_emmc.txt or MT6577_Android_scatter_emmc.txt, depending on which phone you have) for your device and ignore any message that may appear.
[You must be registered and logged in to see this image.]


  • Turn off your phone, remove the battery and replace it after some seconds (and don't turn on the phone).
  • Press F9 (or hit Download button) and connect your phone into the computer via USB data cable.
    The process will start and a red progress bar will appear.
[You must be registered and logged in to see this image.]

[You must be registered and logged in to see this image.]



  • After the red progress bar is complete, there will appear a purple progress bar.
[You must be registered and logged in to see this image.]


  • Right after the purple progress bar is complete, a message will appear underneath it:

    Please insert USB cable in x seconds” and then the download will start right away (you will see the yellow progress bar filling up).
[You must be registered and logged in to see this image.]



  • When the yellow bar is complete, you'll get a popup with a green circle and Download OK message,
    which means that the process has been successfully terminated.
[You must be registered and logged in to see this image.]



  • You can now safely disconnect your phone and turn it on. The process ends here.
Flashing only part of the ROM

  • In case you want to flash just one part of the ROM, that is also possible. In the shown example, only recovery image will be flashed.

    Deselect all parts except the one(s) you want to flash and then press F9 (or hit Download button).
[You must be registered and logged in to see this image.]


  • The tool will immediately show a warning because not all parts are selected, but you should continue anyway. Safely press Yes to continue.
[You must be registered and logged in to see this image.]



  • The download of the chosen partition image will start and after the yellow bar is complete, the popup with the green circle should appear.

[You must be registered and logged in to see this image.]

[You must be registered and logged in to see this image.]


  • Please note that, even though it isn't mandatory to select it on the list of images to flash,
    preloader file must be present in the same folder as the other partition(s) that you want to flash, or else phone will not be able to enter into download mode.

Attention: Please follow the instructions carefully. I will not take any responsibility on whatever may happen with your phone.

Very important warning: Always make sure that you trust the sources of the ROM you download and know that it is meant for your phone.

After flashing a wrong preloader, your phone will be completely dead (can't be powered on, it will not charge and won't be detected anymore by the computer) and there is no way to recover it


link............... SP_Flash_Tool_v3.1224.01.rar


Dowenload here
Back to top Go down
 
Mtk Android (Sp flash tool ) tutorial :)
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» blackberry 8520 APP ERROR 523..DONE
» Flash Sigs : Must Check em Out !
» [Tutorial][YGOPRO]How to add packed custom cards to YGOPRO using card packer
» power tool dragon deck(rate and fix)
» Custom Tutorial Thread

Permissions in this forum:You cannot reply to topics in this forum
۞۞ Shohag Gsm™ ۞۞ :: GSM Mobile Brands Hadware & Software Area- :: Chinese Models & Cloned Phones  :: Chaina Hardware & Hardware-Repair Area-
Jump to: