۞۞ Shohag Gsm™ ۞۞
Welcome to ۞۞Shohag Gsm™️ ۞۞ please join now !!!!

...!!! Keep share you knowledge!!!...
@};- @};-

If your Like Post please Comments

((((((((The most helping forum)))))))
۞۞ Shohag Gsm™ ۞۞
Welcome to ۞۞Shohag Gsm™️ ۞۞ please join now !!!!

...!!! Keep share you knowledge!!!...
@};- @};-

If your Like Post please Comments

((((((((The most helping forum)))))))
۞۞ Shohag Gsm™ ۞۞
Would you like to react to this message? Create an account in a few clicks or log in to continue.



 
HomeLatest imagesSearchAll FRPCracked ZoneRegisterLog inIMEI Chack

 

 Upgrade Samsung Galaxy S i9000 Firmware using Odin Flash Too

Go down 
AuthorMessage
Shohag Gsm™
Upgrade Samsung Galaxy S i9000 Firmware using Odin Flash Too Adminstrator
Upgrade Samsung Galaxy S i9000 Firmware using Odin Flash Too Stars13
Shohag Gsm™


Male Posts : 1531

Points : 128304
Reputation : 43
Birthday : 21/12/1989
Join date : 15/03/2011
Age : 34
Location : In your Hard

Upgrade Samsung Galaxy S i9000 Firmware using Odin Flash Too Empty
PostSubject: Upgrade Samsung Galaxy S i9000 Firmware using Odin Flash Too   Upgrade Samsung Galaxy S i9000 Firmware using Odin Flash Too Icon_minitimeSun Jan 27, 2013 12:12 am


Upgrade Samsung Galaxy S i9000 Firmware using Odin Flash Too






[You must be registered and logged in to see this image.]





flash Samsung Galaxy S i9000 with either leaked, custom ROM or Official release.




Requirements





  • Unlocked Samsung Galaxy S i9000
  • Latest Samsung Kies or Device drivers installed.
  • ODIN 3 version 1.0 (flash program)
  • Upgrade Firmware upgrade File (.tar) can be downloaded from Samsung-Firmware
  • .PIT file (the boot file of the phone generally called 512.pit) which will be included in upgrade file.
  • USB cable



Procedure





  • Open Odin (preferably “Run as Administrator”)
  • Browse the PIT file from extracted firmware upgrade.
  • In PDA, browse the TAR file which is the main file requirement.
  • Optionally if there is any file with CSC in it, browse and select it.
  • Switch off Phone and remove SD Card (if any) and SIM.
  • Connect with USB
  • Hold Volume down + Home Key + Power button till the phone boots in “Download mode”.
  • Press Start button on Odin program window after it detects ID:COM
  • Phone will reboot again and whoa! your Phone is flashed with latest firmware.

[You must be registered and logged in to see this image.]
Disclaimer


  • Take Backup of Contacts, Messages and Calender events and Apps before proceeding as it will erase all data in ROM.
  • I have flashed my Samsung Galaxy S i9000 with official leaked ROM using the following procedure and it worked fine on Windows 7.
  • We are not responsible if you accidentally brick your phone.

Let any firmware release or leak on web, if it
is not available officially for you, flashing with odin is a working
method. After Flashing, the phone is unrooted so, you will have to root Samsung Galaxy S i900 again in one click available for 2.1 Eclair and 2.2 Froyo.







Flashing the device firmware can fix unexpected errors or failures on
the device or when all else fails, it is the only way to restore a
device to working condition after a partial brick or boot loop.



Preparing and Setting up ODIN and Files used to Flash.
-Odin3 version 1.85
or here
Then download the latest Samsung Galaxy S II Original Firwares




Or find and Download the latest firmware Updates

Flashing the Samsung Galaxy S II I9100 Procedures:

1. Extract and Run the ODIN flasher tool.



[You must be registered and logged in to see this image.]




2. Check these checkboxes options: Re-Partition , Auto Reboot , F.Reset Time



[You must be registered and logged in to see this image.]




3. Select the PDA/Modem/CSC/.PIT files in Odin
In the PIT section, select the u1_02_20110310_emmc_EXT4.pit file you downloaded.
In the PDA section, select the CODE_I9100xxxxx_CL161513_REV02_user_low_ship.tar.m d5 file.
In the PHONE section, select the MODEM_I9100xxxxx_REV_02_CL995882.tar.md5 file.
In the CSC section, select the GT-I9100-MULTI-CSC-Oxxxxx.tar.md5 file.



[You must be registered and logged in to see this image.]




4. Prepare the Samsung Galaxy S II into DOWNLOAD MODE.
Turn the phone into the download mode by pressing and holding
VolumeDown+OK+Power at the same time.



[You must be registered and logged in to see this image.]




5. Connect the Device to PC using the DATA cable
Connect your phone with your computer and wait until the drivers are installed.
Make sure the ID:COM box highlighted yellow to know that the handset is connected to the PC properly.
If you still do not get any results, try another USB port on your computer.



[You must be registered and logged in to see this image.]




6. When all binary files needed is ready, Enter the Device into Firmware Downloading process, Click Start.



[You must be registered and logged in to see this image.]



The phone will be flashed and once it’s finished, it will boot up.Do NOT
disconnect the usb-cable, remove the battery or otherwise interrupt
this process!
But if you do not see a blue progress bar on your phone after 5 minute,
take out your phones battery, unplug your phone and start from step 1
again.
7. Handset reboots when flash or download completes
Once you see the message "PASS!", you have successfully flashed your phone.



[You must be registered and logged in to see this image.]


8. Codes to confirm the Downloaded Firmware Version
*#1234#
Full Reset
*2767*3855#
Back to top Go down
 
Upgrade Samsung Galaxy S i9000 Firmware using Odin Flash Too
Back to top 
Page 1 of 1
 Similar topics
-
» How to Flash Update/Upgrade Samsung Galaxy Tab P1000 to 2.3.3 Gingerbread - Proc
» How To Flash Free Samsung I9300 Galaxy S III Firmware
» Samsung Galaxy Firmware Download here
» The First Android 4.1.2 Jelly Bean Firmware for Samsung Galaxy Music S6010 is Online
» Samsung Vibrant Galaxy S T959 flash

Permissions in this forum:You cannot reply to topics in this forum
۞۞ Shohag Gsm™ ۞۞ :: GSM Mobile Brands Hadware & Software Area- :: SAMSUNG  :: Samsung Programs & Flashers-
Jump to: