۞۞ Shohag Gsm™ ۞۞
Welcome to ۞۞Shohag Gsm™ ۞۞ please join now !!!!

...!!! Keep share you knowledge!!!...
@};- @};-

If your Like Post please Comments

((((((((The most helping forum)))))))



 
HomeFAQSearchCracked ZoneRegisterLog inIMEI Chack

Share | 
 

 Flashing And Upgrading Chinese MP4 Player Firmware

View previous topic View next topic Go down 
AuthorMessage
shamim




Posts : 456

Points : 62094
Reputation : 20
Birthday : 15/08/1989
Join date : 20/05/2011
Age : 27

PostSubject: Flashing And Upgrading Chinese MP4 Player Firmware   Mon May 23, 2011 6:51 am

If your are not an audiophile and don't care much about audio/video quality, cheap chinese MP3/MP4 players
are just for you, these devices are quite popular and just get the job
done, since there is no quality control over these devices they do not
last long, one of the most common problems faced with these portable
players is the issue of firmware software corruption, I encountered a
similar problem with my friends PMP which refused to start getting
stuck at loading screen, the only solution was to flash the firmware
but the problem was unavailability of any information and tools to get
the job done, after long research and flashing the firmware I was able
to successfully recover the MP4 player to working condition.

[You must be registered and logged in to see this image.]

Here is an step-by-step tutorial on how to identify your MP4 player,
download its firmware and flash it using appropriate tools :

WARNING : This procedure can render your device dead, so do not try if your player is working fine.


  1. The most important step of the whole process is to correctly
    identify your device CONTROL CHIP and CPU, using wrong firmware or
    flashing tool may cause damage to your device, unscrew and open your
    device and write down all chip id's and motherboard numbers you see,
    you can also try the EasyChips - firmware identification utility but it did not worked for me.

    [You must be registered and logged in to see this image.]
  2. You will now need to download the correct firmware and flashing
    utility for your device, visit sites below and search for your control
    chip and cpu to download the firmware and flashing utility, you can
    also post on user-forums to get help identifying the firmware :

    • S1FW
    • MyMpxPlayer
    • SKMP3

  • In my case the chipset was Sunplus AJ262-V7 and the utility needed to flash it was FRM Pro.
  • Once identified you need to connect your device to computer
    via USB in camera mode (Press A + OK button and plugin USB cord on
    player), for Windows to identify this mode you will need camera drivers
    you need to point Windows Found New Hardware Wizard to Driver
    folder downloaded with the FRM Pro utility above, this will install the
    first camera driver, for correct identification by flashing utility you
    need to install a second camera driver - open Windows Hardware Manager
    and install unidentified camera device drivers by pointing the driver
    wizard to Driver folder used earlier.

  • Now install and launch FSM Pro flashing utility and follow these instructions to install the new firmware.

    [You must be registered and logged in to see this image.]
  • Let the process finish, this will take a while, do not disconnect
    or interrupt the process until you see a success message in log window.

    [You must be registered and logged in to see this image.]
  • Unplug your PMP from computer and it should be working now.
  • Back to top Go down
    shamim




    Posts : 456

    Points : 62094
    Reputation : 20
    Birthday : 15/08/1989
    Join date : 20/05/2011
    Age : 27

    PostSubject: How To Update Sunplus SPMP3050 chip MP4/MP5 Players Firmware   Mon May 23, 2011 6:55 am

    ou will Need to use FRM Pro Tools Firmware Update Utility to Update MP4/MP5 firmware.



    Note:** Before using FRM Pro Tools, please check your PC computer to
    confirm that the AP USB driver for your MP4/MP5 player has been
    installed. If the driver has not been installed, you can download it
    from our files download section. The driver is found in the 3050 driver
    directory.


    Driver installation method is as follows:

    Connect your MP4/MP5 Player SPMP3050 to your PC computer. Your PC will
    prompt you that it has found a new device. To install the driver,
    select the 3050 driver folder, and then select ca536av.inf and ca536ai.inf (2 install files). The PC should then proceed through the driver install process. You can click 'finish' at the end.



    Now your PC should properly recognize your Sunplus MP4/MP5 player.
    These are the next steps to take to update the firmware using FRM PRO TOOLS version 1.1.9a:

    ----------------------------------------------------------------------------



    1. Double-click on the desktop icon of FRM Pro Tools to open the application tool. (DO NOT connect your Sunplus MP4/MP5 player at this time yet.)

    [You must be registered and logged in to see this image.]



    2. Right-click on RSV, then select "Set Working Folder" on menu:

    [You must be registered and logged in to see this image.]



    3. Choose the corresponding mp4/mp5 model in the "DOWNLOAD" folder path:

    [You must be registered and logged in to see this image.]



    4. Right-click on firmware, then select "set file", choose "SPMP3050A.bin"

    [You must be registered and logged in to see this image.]



    5. Return to the basic interface, then click on "Dev Detect Begin" :

    [You must be registered and logged in to see this image.]



    6. Connect the SPMP3050 device, you can see the LOG window display the word "Detect", then click on "Dev Detect End":

    [You must be registered and logged in to see this image.]



    7. If necessary, you can update another SPMP3050 device by simply
    selecting "DOWNLOAD" again and going through steps 6 and 7, until you
    have upgraded all devices.

    [You must be registered and logged in to see this image.]



    8. Please Note: ** If doing this for the first time, you will have
    to go through the following 2-step process. So, if that's the case, go
    to the advanced interface, right-click on the "Working Folder", select
    "Create RSV Image":

    [You must be registered and logged in to see this image.]



    9. In the pop-up interface, select "Enable detect", then click on "Detect blk size":

    [You must be registered and logged in to see this image.]



    10. Select the appropriate folder under "DOWNLOAD" folder for the
    MP4/MP5 device firmware that you want to update. Click the "ISP" button
    to upgrade it:

    [You must be registered and logged in to see this image.]



    11. The tool will start going through the firmware upgrade/update
    process, and once completed, the "Log Window" will give you a "SUCCESS"
    display. This means the firmware update "DOWNLOAD" process has
    completed:

    [You must be registered and logged in to see this image.]
    Back to top Go down
     
    Flashing And Upgrading Chinese MP4 Player Firmware
    View previous topic View next topic Back to top 
    Page 1 of 1
     Similar topics
    -
    » Chinese food
    » Chinese Broccoli
    » Chinese/Japanese teapot 5in tall, genuine or fake ?
    » Law Abiding Citizen Premiere - Oct. 6, Mann's Chinese Theater
    » RCA's Record Player Lineup for 1958

    Permissions in this forum:You cannot reply to topics in this forum
    ۞۞ Shohag Gsm™ ۞۞ :: GSM Mobile Brands Hadware & Software Area- :: Non GSM/Mobile Related  :: Mp3/Mp4 & Game Consoles-
    Jump to: