۞۞ Shohag Gsm™ ۞۞
Welcome to ۞۞Shohag Gsm™ ۞۞ please join now !!!!

...!!! Keep share you knowledge!!!...
@};- @};-

If your Like Post please Comments

((((((((The most helping forum)))))))



 
HomeFAQSearchCracked ZoneRegisterLog inIMEI Chack

Share | 
 

 Working Conditions MTK 6223 CPU

View previous topic View next topic Go down 
AuthorMessage
Shohag Gsm™




Male Posts : 1531

Points : 74884
Reputation : 43
Birthday : 21/12/1989
Join date : 15/03/2011
Age : 26
Location : In your Hard

PostSubject: Working Conditions MTK 6223 CPU   Wed Sep 07, 2011 9:05 am

Working Conditions MTK 6223 CPU

[You must be registered and logged in to see this image.]

Like on MTK 6225 CPU which we have discussed before, so being able to
work with both the CPU requires three main conditions, namely:
1. Working voltage
2. Clock
3. Work orders



Differences that would look so striking on phones that use MTK 6223 CPU
(in this comic on your phone G381i and HT Nexian G10) is where there is
no IC Power as a major regulator of cell phone use MTK 6225 CPU. In this
type of CPU has terintegrated Power management in the CPU itself.

[You must be registered and logged in to see this image.]

In the layout in the Power Management Circuit visible contained in the
CPU is MTK 6223. So that the CPU in addition to functioning as a data
processor also functions as a regulator. For he is a regulator, then
enable the form off and power on the input lines will vbat directly into
the CPU.

Notice the layout of pins on MTK 6235 CPU follows:

[You must be registered and logged in to see this image.]

As in the previous MTK CPU working conditions, then the terms of this
work on any 6223 MTK are equally good or big name tegangannnya. The
voltages are:

- Voltage FiO at 2.8v on pin B7

Input Voltage Out put this one of the main voltage needed by the CPU
directly. If the voltage does not exist then the CPU can not work, and
our phones will experience the death total.


- A sum of 1.8v vCore voltage 8V at pin A7

Stress is also a main voltage required by the CPU to be working.


- Voltage of 2.8v Vana 8V on pin C1

This internal voltage required by IC Power, although not a direct
voltage to the CPU sufficient, but if the voltage is missing will cause
the CPU can not work.


- Voltage of 2.8v Vmem 8V on pin B6

This voltage is needed by flash ic. If voltage is not there then ic
flash as data storage device we will not be able terbooting by the CPU
and the phone we would not be able to live.


Here is an example of the voltage measurement points MTK 6223
[You must be registered and logged in to see this image.]

If there is one that does not stress out, then we can conclude that the
regulator does not function to exclude one of these voltages. The most
correct solution or by the rules is that you must perform the
replacement of MTK, but if you want to do a little pengiritan without
replacing the IC, then you can make jumpers from another large voltage
equal voltage.
Back to top Go down
Shohag Gsm™




Male Posts : 1531

Points : 74884
Reputation : 43
Birthday : 21/12/1989
Join date : 15/03/2011
Age : 26
Location : In your Hard

PostSubject: Re: Working Conditions MTK 6223 CPU   Wed Sep 07, 2011 9:05 am

Clock source of the phone is a component that we call oscilator.


There are two types of clocks on our mobile phones as a CPU working conditions, namely:

- Sleep clock for 32.768Khz

[You must be registered and logged in to see this image.][You must be registered and logged in to see this image.]

Sleep Clock oscillator scheme which I capture the above can be found on
page CPU. When we press on off the power ic will provide responses to
sleep oscillator frequency so that the issue amounted to 32 768 Khz.
This clock will be used by the CPU as one CPU working conditions to be
working.

- RF clock of 26Mhz.
[You must be registered and logged in to see this image.][You must be registered and logged in to see this image.]

Clock frequencies of 26Mhz RF generated by the IC Rf which is derived by
processing data from the RF oscillator clock. That is, if we perform
measurements on the RF output to the CPU and Clock that we are not
getting value for 26Mhz, then it is caused by the rf ic dysfunction or
malfunction of the RF oscillator clock, so that should not produce
output.

However please note, that in order to be able to work, Ic RF voltage VRF
Requires registration 2.8v which is produced by a regulator, ie VRF
Regulator. To be able to release output, then this regulator requires
such a condition that we discussed earlier.
Measurement of RF clock and clock both sleep clock, clock or other clock later can be done by using the frequency counter.

[You must be registered and logged in to see this image.][You must be registered and logged in to see this image.]

Enable on the Enable regulators VXO above is sourced from the CPU.
Ordered to work with the CPU voltage regulator 2.8v sebesat. if we get a
case of VRF was not out at 2.8v, then the phone automatically we will
die because the total absence due to supply voltage to generate RF rf ic
clock to the CPU. Simple steps we can do if we get VRF cases did not
come out with a voltage of 2.8v is doing jumpers from other
voltage-to-voltage VRF, for example from Vmem voltage of 2.8v.
In some phones you'll probably be found where there is no regulator VRF,
you do not need to bother with this. If not found an external regulator
as shown above, then the most likely is the direct VRF Ic produced by
Power or CPU that has been functioning as a regulator.
Back to top Go down
Shohag Gsm™




Male Posts : 1531

Points : 74884
Reputation : 43
Birthday : 21/12/1989
Join date : 15/03/2011
Age : 26
Location : In your Hard

PostSubject: Re: Working Conditions MTK 6223 CPU   Wed Sep 07, 2011 9:06 am

Some work orders actually indirectly I have written above ... shaped
enable regulators. Enable that I have written previously are:

- On-off as to enable the workings of power ic.
During the process of flashing on mobile china, generally we have to
press the on off button to respond to the cpu to do the booting process.
That is, without pressing the on off well when performing the search
process RX / TX and when the flashing, the flashing process itself is
not going to happen.
Note Pin PWRKEY D3 point. This path is the path of the on off on off the entrance to the CPU.
[You must be registered and logged in to see this image.]

- Enable VCO at 2.8v as to enable VRF Regulator
Enable is sourced from the CPU, this command is to order the VRF
regulators to begin working out at 2.8v voltage VRF. course to be worked
out then the regulator output requires input vbat and grounding.
Without both of them then this output would not be out.


- There's one more job orders originating from the internal CPU to CPU
itself is reset, this command at 2.8v. This gives the command to reset
the CPU to start can work, provided all other conditions are perfect
work, both the voltage and clock needed by the CPU.
Note the reset of the scheme in addition to the MTK 6223. Reset pin is
at C3. If on MTK 6225 CPU we learned that this Reset ic Power comes from
the CPU to the phone because there is no Power Ic, then this command
comes from the CPU into the CPU itself.
Measurement of these work orders can be done using avo meter like when you do a voltage measurement
[You must be registered and logged in to see this image.]

From the above discussion of the working conditions we can deduce some
of the main employment requirements CPU chinese mobile phone with MTK
CPU 6225, namely:
1. On Off
2. 2.8v FiO
3. VCore 1.8v
4. Vana 2.8v
5. Vmem 2.8v
6. VRF 2.8v
7. Rf 26Mhz Clock
8. Sleep Clock 32.768Khz
9. Enable VXO 2.8v
Back to top Go down
Sponsored content




PostSubject: Re: Working Conditions MTK 6223 CPU   Today at 8:19 pm

Back to top Go down
 
Working Conditions MTK 6223 CPU
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» Triode ST-70 kit, one side not working, fuse blows when biased past 0.9V
» Wanted - Good working posi
» 2012 (working title) - Work In Progress
» Working with true white background for photoshoots
» waterpump is not working enough

Permissions in this forum:You cannot reply to topics in this forum
۞۞ Shohag Gsm™ ۞۞ :: GSM Mobile Brands Hadware & Software Area- :: Chinese Models & Cloned Phones  :: Chaina Hardware & Hardware-Repair Area-
Jump to: